Home/HighLevel/Troubleshooting/Bounces and blocks
Troubleshooting · Email
Fix: GoHighLevel email bounces and blocks. Read the bounce reason.
A bounce tells you why it failed: a bad address, a full mailbox, a block or a rate limit. Each needs a different fix.
The short answer
GoHighLevel emails bounce or get blocked because of invalid addresses, authentication failures, rate limits such as Gmail's 4.7.28 unusual rate error, or a poor sending reputation, so read the bounce reason in the message details first, because each cause needs a different fix. HighLevel can auto enable email DND on bounced contacts.
Michael is a sponsored HighLevel affiliate. Links to HighLevel use his partner link at no extra cost to you. HighLevel prices and product facts on this page come from HighLevel's own pricing page and help center, checked on the date above.
Causes
What causes HighLevel email bounces and blocks?
Most cases come down to the four causes in this table. Check each one before you change anything.
| Cause | How to check |
|---|---|
| Invalid address | Hard bounce reason |
| Authentication failure | Domain verification status |
| Rate limit | Errors like 4.7.28 |
| Reputation | Complaint and bounce rates |
Diagnose
How do you confirm why an email bounced before you send again?
Open one bounced email and read the reason in the message details. Do not skip this. A bounce reason falls into one of two groups. A permanent failure says the address does not exist or cannot receive mail. A temporary failure or block talks about rate, reputation, policy or authentication. The first is about the contact. The second is about you as a sender.
Then look at the pattern across the send. One bounce on one address is a typo or a dead mailbox. Many bounces at one mailbox provider, with wording about limits such as a 4.7.28 error, is a rate or reputation block at that provider. Many bounces everywhere, right after a domain change, points to authentication.
For the sender side, go to Settings, Email Services, Dedicated Domain and IP and confirm every record shows verified. Then send a test to your own Gmail address, open the original message and check that SPF, DKIM and DMARC all pass. If any fail, go to fix SPF, DKIM or DMARC failing before anything else.
Fix
Fix it step by step.
- Read the bounce reason in the message details.
- Remove or correct invalid addresses.
- Verify SPF, DKIM and DMARC.
- For rate limits, reduce volume and send to engaged contacts.
- Keep auto email DND on bounce enabled.
Still stuck
When to contact support.
If none of these fix it, open Help and Support from the question mark at the top right of your agency view, then start a chat (AI Support Chat or Agent Chat), join a Zoom call or open a ticket. Have your Agency Relationship Number and the Location ID of the subaccount ready, add screenshots of the problem, and turn on Support Access so the team can look inside the account. Only Agency Admins and Agency Users can reach HighLevel support; subaccount users go through their agency.
- Clean lists before importing
If blocks continue with authentication passing and a clean list, send support the sending domain, the full bounce text, the time of the send, the mailbox provider that blocked it and roughly how many emails went out.
To prevent bounces, clean lists before importing, never email a hard bounce twice and leave automatic email DND on bounce switched on. New domains need warming up. The wider checklist is in fix email deliverability problems, and delivered mail that lands in junk is covered in fix emails going to spam.
For the basics, see does HighLevel have email marketing and the rest of the email answers. Not on the platform yet? The GoHighLevel 30 day trial through Michael's link lets you set this up and test it before the first invoice. What your account can do depends on the plan, so check GoHighLevel plans compared.

Hard bounces should never be emailed twice.
Questions
Common questions.
Why is my email bouncing or blocked?
Emails bounce or get blocked because of invalid addresses, authentication failures, rate limits such as Gmail's 4.7.28 unusual rate error, or a poor sending reputation, so read the bounce reason in the message details first, because each cause needs a different fix. HighLevel can auto enable email DND on bounced contacts.
How do I prevent it?
Clean lists before importing, never email a hard bounce twice and leave automatic email DND on bounce switched on. New domains need warming up.
When should I contact HighLevel support?
Contact support once you have checked every cause on this page and it still fails, or when the fix sits on HighLevel's side. If blocks continue with authentication passing and a clean list, send support the sending domain, the full bounce text, the time of the send, the mailbox provider that blocked it and roughly how many emails went out.
What is the difference between a hard bounce and a block?
A hard bounce means the address is invalid and should not be emailed again. A block or rate limit is the receiving provider refusing mail for now because of volume, reputation or authentication.
Should I resend to an address that bounced?
Not if it was a hard bounce. Correct the address or remove the contact. Sending again to invalid addresses hurts your sender reputation.
Why does HighLevel turn on DND after a bounce?
Automatic email DND on bounce stops further sends to an address that cannot receive mail. It protects your reputation, so keep it enabled.
Next step
See it in your own account. Thirty days, every feature.
Start a 30 day trial through Michael's link, build the first system and test it before the first invoice. Usage fees for phone, SMS, email and AI can apply during the trial.
HighLevel has three plans at a flat monthly price, each with unlimited users and contacts. See what each one includes and what it costs.
Compare the PlansStarter, Unlimited and Founder